Table of Contents

1 -  AS ISO/IEC 18000.3-2007 Information technology - Radio frequency identification for item management - Parameters for air interface communications at 13.56 MHz
4 -  PREFACE
5 -  CONTENTS
7 -  INTRODUCTION
9 -  1 Scope
9 -  2 Conformance
9 -  2.1 Claiming conformance
9 -  3 Normative references
10 -  4 Terms and definitions
10 -  5 Symbols and abbreviated terms
10 -  6 Requirements: Physical layer, collision management system and protocol values for 13,56 MHz systems
10 -  6.0 General and applicable to both Modes of this part of ISO/IEC 18000
10 -  6.0.1 Presentation as determined in ISO/IEC 18000-1
10 -  6.0.2 ISO/IEC 18000-3 Interoperability
11 -  6.0.3 ISO/IEC 18000-3 reader conformance/compliance
11 -  6.0.4 ISO/IEC 18000-3 tag compliance.
11 -  6.0.5 Command structure and extensibility
11 -  6.0.6 Mandatory commands
11 -  6.0.7 Optional commands
11 -  6.0.8 Custom commands
11 -  6.0.9 Proprietary commands
12 -  6.1 Physical layer, collision management system and protocols for MODE 1 of this part of ISO/ IEC 18000
12 -  6.1.1 Read/Write system
12 -  6.1.2 Normative Aspects
12 -  6.1.3 Conformance and performance measurement aspects
12 -  6.1.4 Physical Layer
12 -  6.1.5 Protocol and collision management operating method
12 -  6.1.6 Commands
12 -  6.1.7 Parameter tables for interrogator to tag link..
12 -  6.1.8 Parameter tables for tag to interrogator link
12 -  6.1.9 Protocol extension
13 -  6.1.10 Protocol extension- description of collision management method
27 -  6.1.11 Protocol extension commands
37 -  6.1.12 Air interface application laye
38 -  6.2 MODE 2: Physical layer, collision management system and protocols for MODE 2 of this part of ISO/IEC 18000
38 -  6.2.1 Normative aspects: physical and media access control (MAC) parameters: interrogator to tag link
40 -  6.2.2 Tag to interrogator link
43 -  6.2.3 Description of operating method
49 -  6.2.4 Protocol parameters
49 -  6.2.5 Description of protocol operating method
65 -  6.2.6 Collision management parameters
65 -  6.2.7 Description of collision management parameters operating method (informative)
73 -  6.2.8 Tag order sequencing
73 -  6.2.9 Commands
73 -  6.2.10 Air interface application layer
73 -  7 Marking of equipment
74 -  8 Table of characteristic differences between the MODES specified in this part of ISO/ IEC 18000
75 -  Annex A (normative) Phase jitter modulation (PJM)
79 -  Annex B (informative) Known possible interferences between the MODES determined in this part of ISO/IEC 18000
80 -  Annex C (informative) Interrogator pseudo-code for collision management (Mode 1)
81 -  Annex D (informative) Cyclic Redundancy Check (CRC) (16 bit)
83 -  Annex E (informative) Cyclic redundancy check (CRC) mode 2 (32 bit)
86 -  Annex F (informative) Mode 1 IC reference
87 -  Annex G (informative) A description of ISO/IEC 15693 Protocol as used in MODE 1
153 -  Bibliography

Abstract

Adopts IOS/IEC 18000-3:2004 to provide a physical layer, collision management system and protocol values for RFID systems for Item Identification operating at 13.56 MHz.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
Pages
ISBN
Committee	IT-034
Supersedes	DR 06531 CP