Table of Contents

1 -  AS/NZS 4380:2001 MOTOR VEHICLES-CARGO RESTRAINT SYSTEMS-TRANSPORT WEBBING AND COMPONENTS
4 -  PREFACE
5 -  CONTENTS
6 -  FOREWORD
7 -  SECTION 1 SCOPE AND GENERAL REQUIREMENTS
7 -  1.1 SCOPE
7 -  1.2 REFERENCED DOCUMENTS
8 -  1.3 DEFINITIONS
8 -  1.3.1 Acceptable quality level (AQL)
8 -  1.3.2 Accreditation
8 -  1.3.3 Batch
8 -  1.3.4 Certification
8 -  1.3.5 Combined lashing
8 -  1.3.6 Component
8 -  1.3.7 Competent person
8 -  1.3.8 Elongation
8 -  1.3.9 End fitting
8 -  1.3.10 Flat woven textile webbing
8 -  1.3.11 Inspection
8 -  1.3.12 Lashing capacity (LC)
9 -  1.3.13 Length of a multiple-piece load restraint system
9 -  1.3.14 Performance test
9 -  1.3.15 Quality
9 -  1.3.16 Shall
9 -  1.3.17 Should
9 -  1.3.18 Tensile force indicator
9 -  1.3.19 Type test
9 -  1.3.20 Webbing restraint system
11 -  1.4 MARKING
11 -  1.4.1 Complete assembly
11 -  1.4.2 Label
12 -  1.4.3 Tensioning device
12 -  1.5 PACKAGING
13 -  SECTION 2 MANUFACTURING REQUIREMENTS
13 -  2.1 MATERIAL
13 -  2.1.1 Webbing
13 -  2.1.2 Components
13 -  2.2 DESIGN AND MANUFACTURE
13 -  2.2.1 Sewing on webbing
13 -  2.2.2 Webbing attachment without sewing
13 -  2.2.3 Components
14 -  SECTION 3 PERFORMANCE REQUIREMENTS
14 -  3.1 GENERAL
14 -  3.2 TEXTILE WEBBING
14 -  3.3 LOAD-BEARING COMPONENTS
14 -  3.4 TESTING THE ABILITY TO RELEASE UNDER TENSION
15 -  APPENDIX A - PERFORMANCE TESTING
15 -  A1 SCOPE
15 -  A2 APPARATUS
15 -  A3 PROCEDURES
15 -  A3.1 Testing elongation of textile webbing
16 -  A3.2 Testing a complete webbing restraint device
16 -  A3.3 Testing of pre-tension ability
16 -  A3.4 Testing ability to release under tension
17 -  A4 REPORT
18 -  APPENDIX B - INFORMATION TO BE SUPPLIED ON REQUEST
18 -  B1 SCOPE
18 -  B2 INFORMATION
19 -  APPENDIX C - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
19 -  C1 SCOPE
19 -  C2 STATISTICAL SAMPLING
19 -  C3 PRODUCT CERTIFICATION
20 -  C4 SUPPLIER’S QUALITY SYSTEM
20 -  C5 OTHER MEANS OF ASSESSMENT
21 -  APPENDIX D - SELECTION AND USE OF WEBBING RESTRAINT SYSTEMS
21 -  D1 SELECTION
21 -  D2 USE
21 -  D3 FITTINGS
21 -  D4 SUPPLIER’S INSTRUCTIONS
21 -  D5 STABILITY OF LOAD
21 -  D6 MATERIALS
22 -  D7 OPERATING TEMPERATURES
22 -  D8 OVERLOADING
22 -  D9 LIMIT OF TWIST
22 -  D10 PROTECTION
22 -  D11 WITHDRAWAL AND REPAIR
23 -  APPENDIX E - CARE AND MAINTENANCE OF WEBBING RESTRAINT SYSTEMS
23 -  E1 SCOPE
23 -  E2 EXTENDING THE USEFUL LIFE
24 -  E3 MAINTENANCE

Abstract

Specifies requirements for webbing restraint systems for use in the transport industry.

Scope

This Standard specifies requirements for webbing restraint systems for use in the transportation of cargo under normal operating conditions.
The Standard is not intended to apply to either load restraint nets or vehicle curtain sidewalls or their tensioners. Vehicle curtain single walls and their tensioners are not considered to be general cargo restraint systems.
NOTE: Guidelines on information to be supplied with enquiries and orders are given in Appendix B and the means for demonstrating compliance with this Standard are given in Appendix C. Appendix D gives advice on the selection and use of webbing restraint systems. Appendix E sets out the requirements and recommendations on the care and maintenance of webbing restraint systems.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Pending Revision indicates that as a result of the Aged Standards review process, the document needs updating. If no project proposal, meeting the quality criteria, is received within the 12 month timeframe, the document shall be withdrawn.
Pages
ISBN
Committee	ME-048
Supersedes	DR 00345 CP AS/NZS 4380:1996 DR 00344-00346 CP