More info
Table of Contents
1 -
AS/NZS 60928:2000 AUXILIARIES FOR LAMPS-A.C. SUPPLIED ELECTRONIC BALLASTS FOR TUBULAR FLUORESCENT LAMPS-GENERAL AND SAFETY...
4 -
PREFACE
5 -
CONTENTS
6 -
INTRODUCTION
7 -
SECTION 1: GENERAL REQUIREMENTS
7 -
1 Scope
7 -
2 Normative references
9 -
3 Definitions
9 -
3.1 ballast
9 -
3.1.1 independent ballast
9 -
3.1.2 built-in ballast
9 -
3.1.3 integral ballast
9 -
3.1.4 A.C. supplied electronic ballast
9 -
3.1.5 controllable ballasts
9 -
3.1.6 maximum value of lamp power (of a controllable ballast)
10 -
3.1.7 minimum value of lamp power (of a controllable ballast)
10 -
3.1.8 a.c./d.c. supplied electronic ballast for maintained emergency lighting
10 -
3.2 supply voltage
10 -
3.3 working voltage
10 -
3.4 maximum allowed peak voltage
10 -
3.5 supply current
10 -
3.6 live part
10 -
3.7 rectifying effect
10 -
3.8 type test
10 -
3.9 type-test sample
11 -
3.10 rated maximum operating temperature of a ballast case.
11 -
3.11 control terminals
11 -
3.12 control signal
11 -
3.13 cathode dummy resistor
11 -
4 General requirements
11 -
5 General notes on tests
12 -
6 Classification
12 -
7 Marking
12 -
7.1 Mandatory markings
13 -
7.2 Information to be provided, if applicable
13 -
7.3 Marking shall be durable and legible
13 -
SECTION 2: SAFETY REQUIREMENTS
13 -
8 Terminals and cords
13 -
8.1 Terminals
14 -
8.2 Flexible cords
14 -
9 Provision for earthing
14 -
9.1 Protective earth (ground).
15 -
9.2 Functional earth (ground).
15 -
9.3 Frame or chassis.
15 -
10 Creepage distances and clearances
16 -
11 Protection against accidental contact with live parts
16 -
12 Protection of associated components
17 -
13 Moisture resistance and insulation
18 -
14 Electric strength
18 -
15 Abnormal conditions
19 -
16 Fault conditions
20 -
16.1 Short circuit across creepage distances and clearances if they are less than the values specified in clause 10, .....
20 -
16.2 Short circuit across or, if applicable, interruption of semi-conductor devices
20 -
16.3 Short circuit across insulation consisting of covering of lacquer, enamel or textile
20 -
16.4 Short circuit across electrolytic capacitors
20 -
16.5
21 -
17 Screws, current-carrying parts and connections
21 -
18 Resistance to heat and fire
22 -
19 Resistance to corrosion
26 -
Annex A - Test to establish whether a conductive part is a live part which may cause an electric shock
27 -
Annex B - Particular requirements for electronic ballasts with means of protection against overheating
27 -
B.1 Scope
27 -
B.2 Definition
27 -
B.3 General requirements
27 -
B.4 General notes on tests
27 -
B.5 Classification
28 -
B.6 Marking
28 -
B.7 Limitation of heating
30 -
Annex C - Particular additional safety requirements for a.c./d.c. supplied electronic ballasts for maintained emergency light
30 -
C.1 Scope
30 -
C.2 The definifions in clause 2 apply together with the following:
32 -
C.3 Marking
32 -
C.4 General statement
32 -
C.5 Starting conditions
32 -
C.6 Operating conditions
32 -
C.7 Supply current
32 -
C.8 Maximum current in any lead to a cathode
32 -
C.9 Lamp operation current waveform
33 -
C.10 Mains transient overvoltages
33 -
C.11 Pulse voltage from central battery systems
33 -
C.12 Tests for abnormal conditions
33 -
C.13 Temperature cycling test and endurance test
34 -
Annex D - Measurement of high-frequency leakage cuurent
35 -
Annex ZZ - Variations to IEC 60928 for application in Australia and New Zealand
35 -
ZZ1 Introduction
35 -
ZZ2 Variations
Abstract
Specifies safety requirements for electronic ballasts for tubular fluorescent lamps for use on a.c. supplies up to 1000 V at 50 or 60 Hz with operating frequencies deviating from the supply frequency.
Scope
This standard specifies general and safety requirements for electronic ballasts for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tubular fluorescent lamps as specified in IEC 60081 and other tubular fluorescent lamps for high-frequency operation.
Particular requirements for electronic ballasts with means of protection against overheating are given in annex B.
Particular requirements for a.c./d.c. supplied electronic ballasts for maintained emergency lighting are given in annex C.
General Product Information
Published
|
|
Document Type
|
Standard |
Status
|
Current |
Publisher
|
Standards Australia
|
Pages
|
|
ISBN
|
|
Committee
|
EL-041 |
Supersedes
|
|
Superseded By
|
|