Table of Contents

1 -  AS 3495-1997 STAINLESS STEEL NON-PRESSURE PIPES AND FITTINGS
4 -  PREFACE
5 -  CONTENTS
6 -  SECTION 1 SCOPE AND GENERAL
6 -  1.1 SCOPE
6 -  1.2 APPLICATION
6 -  1.3 REFERENCE DOCUMENTS
6 -  1.4 DEFINITIONS
6 -  1.4.1 Collar
6 -  1.4.2 Compatible material
6 -  1.4.3 Component
6 -  1.4.4 Distortion
6 -  1.4.5 Left-hand or right-hand fitting
6 -  1.5 MARKING
7 -  SECTION 2 MATERIALS
7 -  2.1 SCOPE OF SECTION
7 -  2.2 STAINLESS STEEL
7 -  2.3 ELASTOMERIC SEALS
8 -  SECTION 3 DESIGN AND MANUFACTURE
8 -  3.1 SCOPE OF SECTION
8 -  3.2 CONNECTION ENDS
8 -  3.3 THREAD FORMS
8 -  3.3.1 Fastening pipe threads
8 -  3.3.2 Sealing pipe threads
8 -  3.4 DIMENSIONS OF PIPES AND FITTINGS
8 -  3.4.1 General
8 -  3.4.2 Fittings (including disconnector and floor waste gully traps)
9 -  3.4.3 Waterway
9 -  3.4.4 Inspection openings
9 -  3.5 DISCONNECTOR AND FLOOR WASTE GULLY TRAPS (GENERAL)
9 -  3.5.1 Angle of outlet axis
9 -  3.5.2 Waterseal
9 -  3.6 ALTERNATIVE DESIGNS
10 -  SECTION 4 PERFORMANCE REQUIREMENTS
10 -  4.1 SCOPE OF SECTION
10 -  4.2 STRENGTH AND LEAKAGE TEST
10 -  4.3 ENDURANCE TEST
10 -  4.4 PRESSURE TEST OF DIAPHRAGM JOINTS (PAN CONNECTOR AND WASTE FITTINGS)
10 -  4.5 TORQUE TEST
11 -  APPENDIX A - LIST OF REFERENCE DOCUMENTS
12 -  APPENDIX B - STRENGTH AND LEAKAGE TEST
12 -  B1 SCOPE
12 -  B2 PRINCIPLE
12 -  B3 APPARATUS
12 -  B4 TEST CONDITIONS
12 -  B5 PROCEDURE
12 -  B6 REPORT
13 -  APPENDIX C - ENDURANCE TEST- FLEXIBLE JOINTS AND EXPANSION JOINTS
13 -  C1 SCOPE
13 -  C2 PRINCIPLE
13 -  C3 APPARATUS
13 -  C4 TEST CONDITIONS
13 -  C5 PROCEDURE
13 -  C5.1 Internal hydrostatic test
14 -  C5.2 External hydrostatic pressure test
14 -  C5.3 Expansion joints-Endurance test
14 -  C5.4
14 -  C6 REPORT
15 -  APPENDIX D - PRESSURE TEST OF DIAPHRAGM JOINTS (PAN CONNECTOR AND WASTE FITTINGS)
15 -  D1 SCOPE
15 -  D2 PRINCIPLE
15 -  D3 APPARATUS
15 -  D4 TEST CONDITIONS
15 -  D5 TEST SPECIMEN
15 -  D6 PROCEDURE
16 -  D7 REPORT
17 -  APPENDIX E - TORQUE TEST
17 -  E1 SCOPE
17 -  E2 PRINCIPLE
17 -  E3 APPARATUS
17 -  E4 CONDITIONING AND TESTING
17 -  E5 PROCEDURE
17 -  E6 REPORT
19 -  APPENDIX F - PREFERRED DESIGNS OF STAINLESS STEEL NON-PRESSURE PIPE FITTINGS

Abstract

Specifies the requirements for pipes and fittings, for above and below ground non-pressure applications in the operating temperature range from minus 40C to 100C.

RECONFIRMATION NOTICE
Major stakeholders of this publication have reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change.
Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice.
Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 29 August 2018.

Scope

This Standard specifies the requirements for pipes and fittings, for above and below ground non-pressure applications in the operating temperature range from
- 40 C to 100 C.
NOTE: Illustrations used in this Standard are diagrammatic only and are used without prejudice.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Reconfirmed 21/09/2018. This standard has been reconfirmed in Australia in 2018 and remains current in New Zealand. Reconfirmation Notice 21/09/2018
Pages
ISBN
Committee	WS-002
Supersedes	DR 96412