Table of Contents

1 -  AS/NZS 1734:1997 ALUMINIUM AND ALUMINIUM ALLOYS - FLAT SHEET, COILED SHEET AND PLATE
4 -  PREFACE
5 -  CONTENTS
6 -  SECTION 1 SCOPE AND GENERAL
6 -  1.1 SCOPE
6 -  1.2 REFERENCED DOCUMENTS
6 -  1.3 DEFINITIONS
6 -  1.3.1 Alclad sheet
6 -  1.3.2 Batch
6 -  1.3.3 Lateral bow
6 -  1.3.4 Out-of-squareness
7 -  1.3.5 Plate
7 -  1.3.6 Sheet
7 -  1.4 DESIGNATION
7 -  1.4.1 General
7 -  1.4.2 Alloy designation
7 -  1.4.3 Temper designation
7 -  1.5 ROUNDING OF TEST RESULT VALUES
7 -  1.6 MARKING
7 -  1.7 TRACEABILITY
8 -  SECTION 2 MANUFACTURING REQUIREMENTS
8 -  2.1 SCOPE
8 -  2.2 CHEMICAL COMPOSITION
8 -  2.2.1 General
8 -  2.2.2 Chemical analysis
8 -  2.3 FREEDOM FROM DEFECTS
8 -  2.3.1 General
8 -  2.3.2 Surface dressing of plate
8 -  2.4 MECHANICAL PROPERTIES
8 -  2.4.1 Tensile properties
8 -  2.4.2 Bend properties
8 -  2.5 MANUFACTURING TOLERANCES
23 -  SECTION 3 MECHANICAL TESTING REQUIREMENTS
23 -  3.1 SCOPE
23 -  3.2 SAMPLING FOR MECHANICAL TESTING
23 -  3.3 ORIENTATION OF TEST PIECES
23 -  3.3.1 Tensile test pieces
23 -  3.3.2 Bend test piece
23 -  3.4 PREPARATION OF TEST PIECES
23 -  3.4.1 Location of tensile test piece
23 -  3.4.2 Dimensions of tensile test piece
24 -  3.4.3 Bend test piece
24 -  3.5 TENSILE TEST
24 -  3.6 BEND TEST
24 -  3.7 RETESTING
25 -  SECTION 4 MANUFACTURING TOLERANCES
25 -  4.1 SCOPE
25 -  4.2 THICKNESS TOLERANCES
25 -  4.2.1 Sheet and plate-all alloys
25 -  4.2.2 Alclad alloys (Alclad 2024 and Alclad 3004)
25 -  4.3 WIDTH TOLERANCES
25 -  4.4 LATERAL BOW TOLERANCES
25 -  4.4.1 Measurement of lateral bow
25 -  4.4.2 Tolerances
25 -  4.5 LENGTH TOLERANCES
25 -  4.6 SQUARENESS TOLERANCES
26 -  4.7 DIAMETER TOLERANCES
26 -  4.8 FLATNESS TOLERANCES
26 -  4.8.1 Requirements for flatness tolerance
26 -  4.8.2 Methods of measurement of degree of flatness
33 -  APPENDIX A - PURCHASING GUIDELINES
33 -  A1 GENERAL
33 -  A2 INFORMATION TO BE SUPPLIED BY THE PURCHASER
33 -  A3 TEST REQUIREMENTS
33 -  A3.1 Tensile test
33 -  A3.2 Bend test
33 -  A3.3 Other tests
34 -  A3.4 Independent tests
34 -  A4 CERTIFICATES
34 -  A4.1 Certificate of compliance
34 -  A4.2 Test certificate
35 -  APPENDIX B - TYPICAL FABRICATION CHARACTERISTICS AND APPLICATION DATA

Abstract

Specifies requirements for wrought aluminium and aluminium alloy flat sheet, coiled sheet and plate for general engineering purposes. Chemical composition, mechanical properties and allowable tolerances on dimensions are specified. An appendix provides information on typical fabrication characteristics and applications.

Scope

This Standard specifies requirements for wrought aluminium and aluminium alloy flat sheet, coiled sheet and plate for general engineering purposes. It applies to locally manufactured or imported material grades commonly used in Australia and New Zealand.

NOTES:
1 Advice and recommendations on information to be supplied by the purchaser at the time of enquiry or order are contained in the purchasing guidelines set out in Appendix A.
2 Typical fabrication characteristics and application data for wrought aluminium and aluminium alloys are given in Appendix B.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
Pages
ISBN
Committee	MT-003
Supersedes	DR 96073 AS 1734-1986