Table of Contents

1 -  AS 2117-1991 HOSE AND HOSE ASSEMBLIES FOR PETROLEUM AND PETROLEUM PRODUCTS - MARINE SUCTION AND DISCHARGE
4 -  PREFACE
5 -  CONTENTS
6 -  SECTION 1 SCOPE AND GENERAL
6 -  1.1 SCOPE
6 -  1.2 REFERENCED DOCUMENTS
6 -  1.3 CLASSIFICATION AND DESIGNATION
6 -  1.3.1 General
6 -  1.3.2 Type
7 -  1.3.3 Working pressure
7 -  1.3.4 Grade
7 -  1.3.5 Electrical properties
7 -  1.3.6 Designation
7 -  1.4 MATERIALS AND CONSTRUCTION
7 -  1.4.1 General
7 -  1.4.2 Materials
7 -  1.4.3 Dimensions and tolerances
8 -  1.4.4 Construction
8 -  1.5 MARKING
8 -  1.5.1 Hose
8 -  1.5.2 Couplings
8 -  1.5.3 Hose assembly
10 -  SECTION 2 PERFORMANCE REQUIREMENTS
10 -  2.1 RESISTANCE TO HYDROSTATIC PRESSURE
10 -  2.2 HYDROSTATIC BURST PRESSURE
10 -  2.3 RESISTANCE TO VACUUM (TYPE 1 AND TYPE 2)
10 -  2.4 RESISTANCE OF LINING TO LIQUIDS
10 -  2.5 RESISTANCE TO OZONE
10 -  2.6 ELECTRICAL PROPERTIES
10 -  2.6.1 Electrically continuous hose assembl y
10 -  2.6.2 Electrically discontinuous hose assembl y
10 -  2.6.3 Signalling cable hose
10 -  2.7 FLEXIBILITY (TYPES 1, 2 AND 3 ONLY)
10 -  2.7.1 General
10 -  2.7.2 Retention of electrical properties
10 -  2.7.3 Retention of physical properties
10 -  2.8 HOSE AND COUPLING COMPATIBILITY
10 -  2.9 CONTINUED IN-SERVICE PERFORMANCE
12 -  APPENDIX A - PURCHASING GUIDELINES
12 -  A1 GENERAL
12 -  A2 INFORMATION TO BE SUPPLIED BY THE PURCHASER
13 -  APPENDIX B - DETERMINATION OF RESISTANCE OF HOSE TO HYDROSTATIC PRESSURE
13 -  B1 SCOPE
13 -  B2 PRINCIPLE
13 -  B3 APPARATUS
13 -  B4 PROCEDURE
13 -  B5 CALCULATION
13 -  B6 REPORT
14 -  APPENDIX C - DETERMINATION OF FLEXIBILITY OF HOSE*
14 -  C1 SCOPE
14 -  C2 PRINCIPLE
14 -  C3 PROCEDURE
14 -  C4 REPORT
15 -  APPENDIX D - GUIDE TO TESTING CONTINUED IN-SERVICE PERFORMANCE OF HOSE ASSEMBLIES
15 -  D1 SCOPE
15 -  D2 PRINCIPLE
15 -  D3 APPARATUS
15 -  D4 FREQUENCY OF TESTING
15 -  D5 PROCEDURE

Abstract

Specifies requirements for hose and hose assemblies for conveying petroleum and petroleum products at product temperatures up to 70C and in ambient temperatures ranging from -20C to 65C, but does not include requirements for off-shore mooring use. Appendices include a method for the determination of resistance of hose to hydrostatic pressure and a test for flexibility of hose. A guide to testing hose assemblies for in-service performance is also given.

Scope

This Standard specifies requirements for hose and hose assemblies for conveying petroleum and petroleum products at product temperatures up to 70C and in ambient temperatures ranging from -20C to 65C. It applies to hoses commonly used for transferring crude oil and liquefied petroleum products (other than LP gas and natural gas) to and from marine tankers and bunkering vessels or for similar duties ashore.

The Standard does not specify requirements for off-shore mooring use as such hoses are subject to more rigorous conditions of use than those specified in this Standard.

NOTES:
1 Users of this Standard are advised to consult the 'International Oil Tanker and Safety Guide' issued by the Institute of Petroleum, London, which has been widely adopted by the oil industry in Australia as a guide for handling petroleum products.
2 Appendix A contains recommendations and advice on information which should be provided by the purchaser at the time of enquiry or order.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
Pages
ISBN
Committee	RU-001
Supersedes	DR 87106